diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index df499fd..eb6c34a 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -836,7 +836,7 @@
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 #define X_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING true  // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
@@ -846,7 +846,7 @@
 #define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // Set to true to invert the logic of the probe.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -1075,7 +1075,7 @@
  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  *   (e.g., an inductive probe or a nozzle-based probe-switch.)
  */
-//#define FIX_MOUNTED_PROBE
+#define FIX_MOUNTED_PROBE
 
 /**
  * Use the nozzle as the probe, as with a conductive
@@ -1541,7 +1541,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1550,8 +1550,8 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
-//#define ENABLE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
+// #define ENABLE_LEVELING_AFTER_G28
 
 /**
  * Auto-leveling needs preheating
@@ -1672,7 +1672,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
@@ -1681,7 +1681,7 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1742,7 +1742,7 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing